List of top Textile Engineering Questions asked in CUET (PG)

Desizing of a grey cotton fabric having a starch-based size can not be done using \(\underline{\hspace{2cm}}\)

The process of removal of protruding fibers from the surface of fabric is called as \(\underline{\hspace{2cm}}\)

The material flow of the warp sheet through different zones in a sizing machine is \(\underline{\hspace{2cm}}\).
A. Drying zone
B. Size box zone
C. Beaming zone
D. Creel zone

The reactive dyes are applied to Cellulosic fiber in an alkaline dyeing bath, by chemically reacting to form \(\underline{\hspace{2cm}}\) with the hydroxyl group of the fiber.

The monomer used in the manufacture of Nylon 6 fiber is \(\underline{\hspace{2cm}}\)

Which among the following is not a characteristic of a binder?
A. Capable of application by dry cure to form a film, trapping the pigment on the surface of the substrate
B. Provide adhesion of the pigment to the substrate surface
C. Able to crosslink in order to form a protective film
D. Non-elastic properties to allow for bending and stretching of the substrate after printing

Match Type of shed with Position of warps.\[\begin{array}{|l|l|} \hline\textbf{LIST I} & \textbf{LIST II} \\ \textbf{Type of shed} & \textbf{Position of warps} \\ \hline \hline \text{A. Fully open shed} & \text{I. All warp returns to mid-position before the} \\ \hline \text{next shedding} \\ \hline \text{B. Semi-open shed} & \text{II. All ends come down to the bottom} \\ \hline \text{position before the next shedding} \\ \hline \text{C. Center closed shed} & \text{III. Unnecessary movements of the warps are} \\ \hline \text{avoided} \\ \hline \text{D. Bottom closed shed} & \text{IV. A few healds move half the distance from} \\ \hline \text{the depth of the shed and go back to their} \\ \hline \text{top position for next shedding} \\ \hline \end{array}\]

The after treatment of certain direct dyes with 0.25-2% copper sulphate and 1% acetic acid for 20-30 mins at 60°C to improve \(\underline{\hspace{2cm}}\)

The heart loop test of measurement of fabric stiffness is especially used for \(\underline{\hspace{2cm}}\) fabrics.

Which dye is responsible for tendering of cotton?

In \(\underline{\hspace{2cm}}\) weft knitting machine, the needles in the two beds are not face to face but needles in one bed are in between the needles of the other bed.

\(\underline{\hspace{2cm}}\) has the highest Biological Oxygen Demand (BOD).

In \(\underline{\hspace{2cm}}\), the package is driven in frictional contact with the drum.

The Transmission Electron Microscopy (TEM) is used for the study of \(\underline{\hspace{2cm}}\) structure of fibrous material.

In nonwoven fabric manufacturing, the melt spinning process produces \(\underline{\hspace{2cm}}\)

The wool fiber exhibits high elastic recovery among the natural fibers due to its \(\underline{\hspace{2cm}}\)

Match Fibre with Application.\[\begin{array}{|l|l|} \hline \textbf{LIST I} & \textbf{LIST II} \\ \textbf{Fibre} & \textbf{Application} \\ \hline \hline \text{A. Silk fibre} & \text{I. Fire retardant} \\ \hline \text{B. Wool fibre} & \text{II. Directional lustre} \\ \hline \text{C. Nomex fibre} & \text{III. Bulletproof} \\ \hline \text{D. Kevlar fibre} & \text{IV. Thermal insulation} \\ \hline \end{array}\]

In non-woven fabric manufacturing, the surgical face masks are produced by \(\underline{\hspace{2cm}}\)

The cotton fiber exhibits poor crease recovery due to \(\underline{\hspace{2cm}}\)

In case of plain weave fabric, the respective warp and weft counts are 30 tex and 20 tex, with 40 ends per cm and 30 picks per cm. The warp has 10% crimp and weft also 10% crimp. Calculate the weight of fabric in grams/square meter.

The KES-FB module of Kawabata hand evaluation instruments gives \underline{\hspace{2cm}.
A. Linearity of the load elongation curve.
B. Compression resilience.
C. Tensile energy.
D. Bending rigidity.}

The strength of fiber is usually measured in bundle form because there is better correlation between fiber bundle strength and \(\underline{\hspace{2cm}}\)

Arrange the following transition temperatures given by Differential Scanning Calorimetry (DSC) in ascending order.
A. Melting temperature
B. Crystallization temperature
C. Degradation temperature
D. Glass transition temperature

To prevent the growth of microorganisms, \(\underline{\hspace{2cm}}\) is added to the size paste.