>
TS PGECET 2026
List of top Questions asked in TS PGECET- 2026
Baffles in the shell side of a shell and tube heat exchanger
TS PGECET - 2026
TS PGECET
Chemical Engineering
Heat Transfer
The thermal conductivity is minimum for
TS PGECET - 2026
TS PGECET
Chemical Engineering
Heat Transfer
In a heat exchanger, floating head is provided to
TS PGECET - 2026
TS PGECET
Chemical Engineering
Heat Transfer
LMTD for counter flow and parallel flow heat exchanger will be the same, when
TS PGECET - 2026
TS PGECET
Chemical Engineering
Heat Transfer
For a blackbody, the wavelength at which the maximum monochromatic emissive power occurs is
TS PGECET - 2026
TS PGECET
Chemical Engineering
Heat Transfer
In a feed forward multiple effect evaporator unit
TS PGECET - 2026
TS PGECET
Chemical Engineering
Heat Transfer
The most efficient equipment for removal of sub-micron dust particles from blast furnace gas is
TS PGECET - 2026
TS PGECET
Chemical Engineering
Pollution control and treatment of effluents
Crushing efficiency is the ratio of
TS PGECET - 2026
TS PGECET
Chemical Engineering
Mechanical Unit Operations
In a fertilizer plant, in which of the following equipment, molten ammonium nitrate is mixed with ground lime-stone
TS PGECET - 2026
TS PGECET
Chemical Engineering
Mechanical Unit Operations
In continuous filtration (at a constant pressure drop), filtrate flow rate varies inversely as
TS PGECET - 2026
TS PGECET
Chemical Engineering
Mechanical Unit Operations
Which one of the following is valid for a laminar flow of filtrate through a cake deposited on septum?
TS PGECET - 2026
TS PGECET
Chemical Engineering
Mechanical Unit Operations
Weber number is the ratio of
TS PGECET - 2026
TS PGECET
Chemical Engineering
Fluid Mechanics
For continuous reverse air cleaning in a fabric filter, gas-to-fabric ratio normally varies from
TS PGECET - 2026
TS PGECET
Chemical Engineering
Mechanical Unit Operations
Sorting classifier uses a sink-and-float method to separate particles based on the
TS PGECET - 2026
TS PGECET
Chemical Engineering
Mechanical Unit Operations
During size reduction, the optimum speed of ball mill must be
TS PGECET - 2026
TS PGECET
Chemical Engineering
Mechanical Unit Operations
In a gyratory crusher, the size reduction is effected primarily by
TS PGECET - 2026
TS PGECET
Chemical Engineering
Mechanical Unit Operations
If the frequency of the stirrer in a mixing tank is increased by a factor of 2 while all other parameters are kept constant, by what factor is the power requirement increased at high Reynolds number?
TS PGECET - 2026
TS PGECET
Chemical Engineering
Mechanical Unit Operations
The velocity distribution in the turbulent boundary layer follows
TS PGECET - 2026
TS PGECET
Chemical Engineering
Fluid Mechanics
For a centrifugal pump with a specific impeller diameter, operating at a fixed speed and handling a fluid of constant density
TS PGECET - 2026
TS PGECET
Chemical Engineering
Fluid Mechanics
Fluids which show an apparent increase in viscosity with time are called
TS PGECET - 2026
TS PGECET
Chemical Engineering
Fluid Mechanics
Cavitation can be prevented by
TS PGECET - 2026
TS PGECET
Chemical Engineering
Fluid Mechanics
A rotameter
TS PGECET - 2026
TS PGECET
Chemical Engineering
Fluid Mechanics
High pressure steam is expanded adiabatically and reversibly through a well-insulated turbine which produces some shaft work. If the enthalpy change and entropy change across the turbine are represented by $\Delta H$ and $\Delta S$ respectively for this process, then:
TS PGECET - 2026
TS PGECET
Chemical Engineering
Thermodynamics
Generalized compressibility factor chart is a plot of:
TS PGECET - 2026
TS PGECET
Chemical Engineering
Thermodynamics
For a fully turbulent flow ($\text{Re} \gt 10^5$) in a pipe of diameter $d$, with a constant pressure gradient, the volumetric flow rate ($Q$) of an incompressible fluid varies with the diameter as:
TS PGECET - 2026
TS PGECET
Chemical Engineering
Fluid Mechanics
Prev
1
...
88
89
90
91
92
...
149
Next