Step 1: Part (i): Identify the elements:
Element X: current and voltage are in phase, so X is a pure resistor \(R\).
Element Y: the voltage leads the current. This is the behaviour of an inductor \(L\), where the current lags the voltage.
Element Z: the current leads the voltage. This is the behaviour of a capacitor \(C\).
The printed phase angle is \(\pi/4\), not \(\pi/2\). That means the practical inductor and capacitor also carry some resistance, since \(\tan\phi = X/R = 1\). An ideal inductor or capacitor would give exactly \(\pi/2\). In every case, the sign of the phase tells the type: Y is inductive, Z is capacitive.
Step 2: Part (ii): Impedance of the series R, L, C circuit:
Connect R, L and C in series to the source \(v = v_m \sin\omega t\). The same current \(i = i_m \sin(\omega t + \phi)\) flows in all three. Draw a phasor diagram with the current as the reference.
The voltage across R is \(V_R = iR\), in phase with the current. The voltage across L is \(V_L = iX_L\), and it leads the current by \(\pi/2\), with \(X_L = \omega L\). The voltage across C is \(V_C = iX_C\), and it lags the current by \(\pi/2\), with \(X_C = 1/\omega C\).
\(V_L\) and \(V_C\) point in opposite directions, so their resultant is \(|V_L - V_C|\), perpendicular to \(V_R\). Taking \(X_L > X_C\):
\[ V^2 = V_R^2 + (V_L - V_C)^2 = i_m^2\left[R^2 + (X_L - X_C)^2\right] \]
The impedance is the ratio of the peak voltage to the peak current:
\[ Z = \frac{V_m}{i_m} = \sqrt{R^2 + \left(\omega L - \frac{1}{\omega C}\right)^2} \]
The phase angle between voltage and current is given by \(\tan\phi = \dfrac{X_L - X_C}{R}\).
Variation of current with frequency: the current amplitude is \(i_m = \dfrac{v_m}{Z}\). At low frequency \(X_C\) is large, so \(Z\) is large and \(i_m\) is small. At high frequency \(X_L\) is large, so again \(Z\) is large and \(i_m\) is small. At \(\omega_0 = 1/\sqrt{LC}\) the reactances cancel, \(Z = R\) is minimum, and \(i_m = v_m/R\) is maximum.
The graph of \(i_m\) against \(\omega\) (or \(\nu\)) is a bell-shaped curve. It starts near zero, rises to a sharp peak of height \(v_m/R\) at \(\omega_0\), and then falls back to zero. A smaller R gives a taller and sharper peak.
Step 3: Part (iii): Conditions in a series LCR circuit:
(a) Minimum impedance: \(Z\) is smallest when the reactive term vanishes, \(X_L = X_C\). That is \(\omega L = 1/\omega C\), or \(\omega = \omega_0 = 1/\sqrt{LC}\). Then \(Z_{\min} = R\), and the circuit is in resonance.
(b) Wattless current: the average power is \(P = V_{rms}I_{rms}\cos\phi\). The current is wattless when \(P = 0\), that is, \(\cos\phi = 0\) and \(\phi = \pi/2\). With \(\cos\phi = R/Z\), this needs \(R = 0\). So the current is wattless when the circuit has only an inductor or only a capacitor (or ideal L and C with no resistance). The source gives energy to the circuit in one quarter-cycle and takes it back in the next, so there is no net power loss.
Final Answer:
(i) X is a resistor, Y an inductor and Z a capacitor. (ii) The impedance is the square root of R squared plus the square of (XL - XC); the current peaks at the resonant frequency. (iii) Impedance is minimum when XL = XC, and the current is wattless when R = 0 (phase difference of 90 degrees).
\[ \boxed{Z = \sqrt{R^2 + (X_L - X_C)^2}} \]