List of top Questions asked in CUET (PG)

The freezing time to get 90% overrun in Ice-cream for continuous freezer.

Arrange the following steps in sequential order for obtaining a unit hydrograph:
A. Separation of base flow
B. Estimating the surface runoff in volume
C. Estimating the surface runoff in depth
D. Dividing surface runoff ordinates by depth of runoff
Choose the correct answer from the options given below :

Arrange the following stages of engineering surveys to be done for a new highway alignment project in the correct sequence:
A. Reconnaissance
B. Map study
C. Preliminary survey
D. Final location
E. Detailed survey
Choose the correct answer from the options given below :

Arrange the following components of a typical flexible pavement from bottom to top in correct sequence:
A. Prepared soil subgrade
B. Granular subbase cum drainage layer
C. Granular base course
D. Surface course
Choose the correct answer from the options given below :

Arrange the following parts of a canal system in the correct sequence :
A. Head works
B. Distributary
C. Branch canal
D. Minor
E. Main canal
Choose the correct answer from the options given below :

Arrange the following design steps for the design of channel section on the basis of Lacey's Theory in the correct sequence :
A. Finding out the perimeter
B. Finding out the velocity
C. Calculation of the silt factor
D. Finding out the area
Choose the correct answer from the options given below:

Arrange the following building materials in the increasing order of density of materials :
A. Granite
B. River sand
C. Water
D. Steel
Choose the correct answer from the options given below:

Arrange the following operations in correct order for treating raw surface water to make it suitable for drinking purpose:
A. Screening
B. Filtration
C. Sedimentation
D. Disinfection
Choose the correct answer from the options given below:

Arrange the following checks in the correct order during R.C beam design:
A. Deflection check
B. Flexural strength design
C. Crack width control
D. Shear strength check
Choose the correct answer from the options given below :

Arrange the following sludge treatment unit operations and processes in chronological order:
A. Conditioning
B. Dewatering
C. Concentration
D. Digestion
E. Incineration
Choose the correct answer from the options given below:

Arrange the following temporary adjustment of the theodolite in the correct sequence :
A. Centering
B. Elimination of parallax
C. Levelling
D. Setting
Choose the correct answer from the options given below :

When flow is critical through open channel :
A. The specific energy is minimum for a given discharge.
B. The discharge is maximum for a given specific energy.
C. The specific force is minimum for a given discharge.
D. Froude number of the flow is equal to unity.
Choose the correct answer from the options given below :

The design strength of a tension member is governed by:
A. Rupture at a critical section
B. Yielding of gross area
C. Block shear of end region
Choose the correct answer from the options given below :

The strength of concrete depends on :
A. Type of mortar
B. Proportion between coarse and fine aggregates
C. Water-Cement ratio
D. Temperature at the time of mixing
Choose the correct answer from the options given below :

Consider the following statements :
A. The quality of waste water is determined on the basis of dissolved oxygen.
B. The BOD test is based on dissolved oxygen.
C. Determination of dissolved oxygen also helps in controlling corrosion.
Choose the correct answer from the options given below:

The coefficient of permeability depends upon :
A. Void ratio of the soil
B. Duration of flow
C. Equivalent diameter of the soil grains
Choose the correct answer from the options given below :

Nominal cover to reinforcement is provided to :
A. Protect reinforcement against corrosion.
B. Provide shear resistance.
C. Protect reinforcement against fire.
D. Develop sufficient bond strength along surface area of reinforcement bars.
Choose the correct answer from the options given below :

Which of the following assumptions are made in the force analysis of simple trusses?
A. All members have same cross-sectional area.
B. The bending resistance of all the members is small in comparison with their axial force resistance.
C. All the external loads are applied directly or indirectly at the joints.
D. All joints are idealized to be frictionless hinges.
Choose the correct answer from the options given below :

Consider the following modes regarding the failure of an axially loaded column:
A. Local buckling
B. Squashing
C. Joint buckling
Choose the correct answer from the options given below:

Length of plastic hinge of a beam depends on :
A. Span of the beam
B. Type of loading
C. Shape of cross-section
D. Yield strength of steel
Choose the correct answer from the options given below :

Following are the statements for a square matrix A:
A. If A is invertible then $det(A) \neq 0$
B. If $det(A) = 0$, A has no inverse
C. All eigen values of A are always positive
D. $A^T A$ is always invertible if A is invertible
Choose the correct answer from the options given below :

Consider the following in the context of variations in magnetic declination:
A. Secular
B. Diurnal
C. Annual
D. Regular
Choose the correct answer from the options given below :

Given below are two statements: one is labelled as Assertion (A) and the other is labelled as Reason (R).
Assertion (A): Unit hydrograph theory is not applicable to catchment areas larger than 5000 sq.km.
Reason (R): Rainfall is not uniformly distributed on large catchment areas.
In the light of the above statements, choose the most appropriate answer from the options given below:

The sight distance available on a road to a driver at any instance depends on:
A. Features of the road ahead
B. Height of the driver's eye above the road surface
C. Height of the object above the road surface
Choose the correct answer from the options given below:

Given below are two statements: one is labelled as Assertion (A) and the other is labelled as Reason (R).
Assertion (A): Terzaghi's theory of consolidation considers only primary consolidation.
Reason (R): Secondary consolidation takes place only at the end of the primary consolidation.
In the light of the above statements, choose the most appropriate answer from the options given below: