Question:
Two wires of the same material having equal area of cross section have lengths L and 2L. Their respective resistances are in the ratio
Two wires of the same material having equal area of cross section have lengths L and 2L. Their respective resistances are in the ratio
Updated On: Jun 8, 2024
- 2:01
- 1:01
- 1:02
- 1:03
Show Solution
Verified By Collegedunia
The Correct Option is C
Solution and Explanation
Answer (c) 1 : 2
Was this answer helpful?
0
0
Top KEAM Physics Questions
- A body oscillates with SHM according to the equation (in SI units), $x = 5 cos \left(2\pi t +\frac{\pi}{4}\right) .$ Its instantaneous displacement at $t = 1$ second is
Kepler's second law (law of areas) of planetary motion leads to law of conservation of
- Two capillary tubes A and B of diameter $1\, mm$ and $2\, mm$ respectively are dipped vertically in a liquid. If the capillary rise in A is 6 cm, then the capillary rise in B is
- In the circuit given in figure, 1 and 2 are ammeters. Just after key K is pressed to complete the circuit, the reading will be
- A plate has a length $ 5\pm 0.1\text{ }cm $ and breadth $ 2\pm 0.01\text{ }cm $ . Then the area of the plate is:
View More Questions
Top KEAM Resistance Questions
- A uniform wire of resistance 9 $\Omega$ is joined end-to-end to form a circle. Then the resistance of the circular wire between any two diametrically opposite points is
- The resistance of a wire at room temperature $ 30{}^\circ C $ is found to be $ 10\,\Omega $ . Now to increase the resistance by 10%, the temperature of the wire must be [The temperature coefficient of resistance of the material of the wire is $ 0.002/{}^\circ C $ ]
- A metallic cylindrical wire 'A' has length 10 cm and radius 3 mm. Another hollow cylindrical wire 'B' of the same metal has length 10 cm, inner radius 3 mm and outer radius 4 mm. The ratio of the resistance of the wires A to B is:
- Find the effective resistance between points A and B. Each resistance is equal to R.
- If one cell is connected wrongly in a series combination of four cells each of e.m.f. 1.5 V and internal resistance of 0.5 Ω, then the equivalent internal resistance of the combination is
View More Questions
Top KEAM Questions
- i.$\quad$ They help in respiration ii.$\quad$ They help in cell wall formation iii.$\quad$ They help in DNA replication iv. $\quad$They increase surface area of plasma membrane Which of the following prokaryotic structures has all the above roles?
- A body oscillates with SHM according to the equation (in SI units), $x = 5 cos \left(2\pi t +\frac{\pi}{4}\right) .$ Its instantaneous displacement at $t = 1$ second is
- The pH of a solution obtained by mixing 60 mL of 0.1 M BaOH solution at 40m of 0.15m HCI solution is
Kepler's second law (law of areas) of planetary motion leads to law of conservation of
- If $\int e^{2x}f' \left(x\right)dx =g \left(x\right)$, then $ \int\left(e^{2x}f\left(x\right) + e^{2x} f' \left(x\right)\right)dx =$
View More Questions
Concepts Used:
Resistance
Resistance is the measure of opposition applied by any object to the flow of electric current. A resistor is an electronic constituent that is used in the circuit with the purpose of offering that specific amount of resistance.
R=V/I
In this case,
v = Voltage across its ends
I = Current flowing through it
All materials resist current flow to some degree. They fall into one of two broad categories:
- Conductors: Materials that offer very little resistance where electrons can move easily. Examples: silver, copper, gold and aluminum.
- Insulators: Materials that present high resistance and restrict the flow of electrons. Examples: Rubber, paper, glass, wood and plastic.
Resistance measurements are normally taken to indicate the condition of a component or a circuit.
- The higher the resistance, the lower the current flow. If abnormally high, one possible cause (among many) could be damaged conductors due to burning or corrosion. All conductors give off some degree of heat, so overheating is an issue often associated with resistance.
- The lower the resistance, the higher the current flow. Possible causes: insulators damaged by moisture or overheating.