Question:
Which of the following emulsifiers has the highest HLB value?
Which of the following emulsifiers has the highest HLB value?
Updated On: Feb 24, 2026
- Span 80
- Acacia
- Tween 80
- Sodium lauryl sulfate
Show Solution
Verified By Collegedunia
The Correct Option is D
Solution and Explanation
To determine which emulsifier has the highest Hydrophilic-Lipophilic Balance (HLB) value among the given options, it's essential to understand this concept. The HLB system is used to classify surfactants based on their affinity for water and oil, ranging from 0 to 20.
An emulsifier with a high HLB value is more hydrophilic (water-loving), whereas a low HLB value indicates a more lipophilic (oil-loving) nature:
- Sodium lauryl sulfate - This is a widely known anionic surfactant with a very high HLB value, typically around 40. It is highly hydrophilic, suitable for forming oil-in-water emulsions.
- Tween 80 - A nonionic surfactant with an HLB value of approximately 15. It is also used in oil-in-water emulsions but has a lower HLB than sodium lauryl sulfate.
- Span 80 - Another nonionic surfactant with a low HLB value of around 4.3, making it more suitable for water-in-oil emulsions.
- Acacia - Naturally occurring emulsifier, typically not classified by HLB values but behaves more hydrophilically than Span 80.
From this analysis, Sodium lauryl sulfate has the highest HLB value. Thus, the correct answer is:
Sodium lauryl sulfate
Was this answer helpful?
0
0
Top GPAT Pharmaceutics Questions
- Which of the following is an example of a thermosetting plastic material?
- Which of the following vehicles (not required to be sterile, but must be pyrogen free) is intended to be used in the manufacture of injectable products to be sterilized after preparation?
A typical skin cream consisting of stearic acid, potassium hydroxide, glycerin, water, preservative and perfume, would be commonly known as:
- Given below are two statements, one is labelled as Assertion A and the other is labelled as Reason R
Assertion A: The pressure filling method for filling pharmaceutical aerosol is usually preferred over cold filling method
Reason R: Because with pressure filling method high production speed can be achieved and less propellant is lost.
In light of the above statements, choose the correct answer from the options given below - Given below are two statements, one is labelled as Assertion A and the other is labelled as Reason R
Assertion A: In the manufacturing of glycero‐gelatin suppositories, overfilling of mould is necessary.
Reason R: Glycero‐gelatin bases contract very little on cooling and the excess cannot be neatly removed.
In light of the above statements, choose the correct answer from the options given below
View More Questions
Top GPAT Emulsions Questions
- In treating immunodeficiency disease the goal is to maintain lgG levels at about :
- Theories of emulsification are characterized by one of the following EXCEPT:
- Amixture of emulsifier A and emulsifier B with values of 4 and 14 respectively are to be mixed in a proportion to get mixture with required HLB 12. What is the weight of individual emulsifier that is to be taken to have a total weight of 7 gm ?
- Globule size of parenteral emulsion should be
- All are true EXCEPT......................
View More Questions
Top GPAT Questions
- Match the symbols in the List I with the terms used in the List II of conductance measurements, and
List I
SymbolsList II
TermsA \(\Omega^{-1}\) I Specific conductance B \(∧\) II Electrical conductance C k III Specific resistance D \(\rho\) IV Equivalent conductance
Choose the correct answer from the options given below: - Cottrell’s method is used for the measurement of:
- Match the statements in List I with their correct answers in List II, respectively, in respect to modified 1st law of thermodynamics, and
List I
List II
A Constant heat (q = 0) I Isothermal B Reversible process at constant temperature (dT = 0) II Isometric C Constant volume (dV = 0) III Adiabatic D Constant pressure (dP = 0) IV Isobar
Choose the correct answer from the options given below: - Boric acid with molecular weight 61.83 was partitioned between water and amyl alcohol at 25 °C. The amount of boric acid was determined to be 0.24 g in 250 ml of amyl alcohol and 0.32 g in 100 ml water. The partition coefficient of boric acid between water and amyl alcohol, when calculated at molar concentration for each of the solution, is:
- Drugs ‘A’, ‘B’ and ‘C’ follow zero order, first order and second order degradation kinetics, respectively, but have the same rate constant. Which of the following statement is true in this respect:
View More Questions