Question:
What is the Indian Standard for pre-stressed concrete?
What is the Indian Standard for pre-stressed concrete?
Show Hint
Important IS Codes:
\[
\begin{aligned}
\text{IS 456} &\rightarrow \text{RCC}
\text{IS 1343} &\rightarrow \text{Prestressed Concrete}
\text{IS 800} &\rightarrow \text{Steel Structures}
\text{IS 10262} &\rightarrow \text{Concrete Mix Design}
\end{aligned}
\]
Updated On: Jul 24, 2026
- IS 1343
- IS 456
- IS 10262
- IS 800
Show Solution
Verified By Collegedunia
The Correct Option is A
Solution and Explanation
Concept:
Indian Standards prescribe separate codes for different construction materials and structural systems.
The code of practice for prestressed concrete is
\[
\boxed{\text{IS 1343 : Code of Practice for Prestressed Concrete}}
\]
Other important Indian Standards include:
• IS 456 -- Plain and Reinforced Concrete.
• IS 800 -- General Construction in Steel.
• IS 10262 -- Concrete Mix Proportioning.
Step 1: Recall the relevant IS code. Prestressed concrete structures are designed according to \[ \boxed{\text{IS 1343}.} \]
Step 2: Select the correct option. Therefore, \[ \boxed{(A)\;\text{IS 1343}.} \]
• IS 456 -- Plain and Reinforced Concrete.
• IS 800 -- General Construction in Steel.
• IS 10262 -- Concrete Mix Proportioning.
Step 1: Recall the relevant IS code. Prestressed concrete structures are designed according to \[ \boxed{\text{IS 1343}.} \]
Step 2: Select the correct option. Therefore, \[ \boxed{(A)\;\text{IS 1343}.} \]
Was this answer helpful?
0
0
Top AP PGECET Civil Engineering Questions
The elongation of a conical bar of length L under the action of its own weight is ___ that of a prismatic bar of the same length.
- A steel cylinder of diameter 100 mm and a copper tube of an outer diameter 200 mm are compressed between the plates of a press. If the ratio of their moduli (steel to copper) is 15/8, what is the ratio of their stresses in steel (\( \sigma_s \)) and copper (\( \sigma_c \))?
- In ___\ bending, the direction of the neutral axis will not be perpendicular to the plane of bending.
- If the thin cylindrical shell having diameter \( D \) and subjected to internal pressure \( p \), the ratio of longitudinal pressure to hoop stress is equal to
- The maximum shear stress in a Mohr’s stress circle is equal to
View More Questions
Top AP PGECET Prestressed Concrete Design Questions
- The grade of concrete used for prestressed concrete shall not be less than
- The profile of the prestressing steel in prestressed concrete member follows
- Most common method of prestressing used for factory production is ........
- The minimum cover in any pretensioned - prestressed concrete member located in an aggressive environment is ........
- Which of the following agent does not enhance the workability of concrete?
View More Questions
Top AP PGECET Questions
- If 125V is applied across a 250V, 100W incandescent bulb, the power consumed will be _____ .
- The power consumed by a coil is 300 watts when connected to a 30V DC source and 108 watts when connected to a 30V AC source. The reactance of the coil is ____ .
The supply voltage magnitude \( |V| \) of the circuit shown below is ____ .
A two-port network is defined by the relation
\(\text{I}_1 = 5V_1 + 3V_2 \)
\(\text{I}_2 = 2V_1 - 7V_2 \)
The value of \( Z_{12} \) is:- Which of the following theorems is the dual of Norton’s theorem?
View More Questions