In an experiment, the length of an object is measured to be 6.50 cm. This measured value can be written as 0.0650 m.The number of significant figures on 0.0650m is
- 3
- 4
- 2
- 5
The Correct Option is A
Solution and Explanation
The correct answer is option (A): 3
Significant figures refer to the digits that carry meaning contributing to the precision of a number. The rules to determine significant figures are:
- All non-zero digits are significant.
- Zeros between non-zero digits are significant.
- Leading zeros (zeros before the first non-zero digit) are not significant.
- Trailing zeros (zeros after a decimal and a non-zero digit) are significant.
- In scientific (exponential) notation, only the number before the exponent counts for significant figures.
Given number: \( 0.0650 \)
- Leading zeros "0.0" are not significant.
- Digits "6", "5", and the trailing zero "0" (after decimal) are significant.
So, the number of significant figures = 3
Answer: Option (A) — 3 significant figures
Top Questions on Units and measurement
- When both jaws of a vernier calipers touch each other, zero mark of the vernier scale is right to the zero mark of main scale. 4th mark on vernier scale coincides with a certain mark on the main scale. While measuring the length of a cylinder, observer observes 15 divisions on main scale and 5th division of vernier scale coincides with a main scale division. Measured length of cylinder is ________ mm. (Least count of Vernier calliper = \(0.1\) mm)
- JEE Main - 2026
- Physics
- Units and measurement
- Four persons measure the length of a rod as 20.00 cm, 19.75 cm, 17.01 cm and 18.25 cm. The relative error in the measurement of average length of the rod is :
- JEE Main - 2026
- Physics
- Units and measurement
- Two cars $A$ and $B$ each of mass $10^3$ kg are moving on parallel tracks separated by a distance of $10$ m, in same direction with speeds $72$ km/h and $36$ km/h. The magnitude of angular momentum of car $A$ with respect to car $B$ is _________ J.s.
- JEE Main - 2026
- Physics
- Units and measurement
- Match the column
- JEE Main - 2026
- Physics
- Units and measurement
- Time period of a spring-block system is given by \(T = 2\pi\sqrt{\dfrac{m}{k}}\). If mass of the block is given by \(m = 10\,\text{g} \pm 10\,\text{mg}\) and time period is measured using a stopwatch having least count of \(2\,\text{s}\) and was found to be \(60\,\text{s}\) for \(50\) oscillations, then find the % error in measurement of \(k\).
- JEE Main - 2026
- Physics
- Units and measurement
Questions Asked in WBJEE exam
What are the charges stored in the \( 1\,\mu\text{F} \) and \( 2\,\mu\text{F} \) capacitors in the circuit once current becomes steady?
- WBJEE - 2026
- Capacitors and Capacitance
Which one among the following compounds will most readily be dehydrated under acidic condition?
- WBJEE - 2026
- Organic Reactions
Manufacturers supply a zener diode with zener voltage \( V_z=5.6\,\text{V} \) and maximum power dissipation \( P_{\max}=\frac14\,\text{W} \). This zener diode is used in the circuit shown. Calculate the minimum value of the resistance \( R_s \) so that the zener diode will not burn when the input voltage is \( V_{in}=10\,\text{V} \).
- WBJEE - 2026
- Zener Diodes
Two charges \( +q \) and \( -q \) are placed at points \( A \) and \( B \) respectively which are at a distance \( 2L \) apart. \( C \) is the midpoint of \( AB \). The work done in moving a charge \( +Q \) along the semicircle CSD (\( W_1 \)) and along the line CBD (\( W_2 \)) are
- WBJEE - 2026
- electrostatic potential and capacitance
A piece of granite floats at the interface of mercury and water. If the densities of granite, water and mercury are \( \rho, \rho_1, \rho_2 \) respectively, the ratio of volume of granite in water to that in mercury is
- WBJEE - 2026
- Buoyancy and Floatation
Concepts Used:
Units and Measurement
Unit:
A unit of a physical quantity is an arbitrarily chosen standard that is broadly acknowledged by the society and in terms of which other quantities of similar nature may be measured.
Measurement:
The process of measurement is basically a comparison process. To measure a physical quantity, we have to find out how many times a standard amount of that physical quantity is present in the quantity being measured. The number thus obtained is known as the magnitude and the standard chosen is called the unit of the physical quantity.
Read More: Fundamental and Derived Units of Measurement
System of Units:
- CGS system
- FPS system
- MKS system
- SI units
Types of Units:
Fundamental Units -
The units defined for the fundamental quantities are called fundamental units.
Derived Units -
The units of all other physical quantities which are derived from the fundamental units are called the derived units.