The length of a given cylindrical wire is increased to double of its original length. The percentage increase in the resistance of the wire will be ______%.
Correct Answer: 300
Solution and Explanation
Volume is constant so on length doubled
Area is halfed so
\(R=p\frac{l}{A}\)
and
\(R'=p\frac{2l}{\frac{A}{2}}=4p\frac{l}{A}=4R\)
So percentage increase will be
R%\(=\frac{4R-R}{r}×100=300%\)
Top Questions on Resistance
- A wire of resistance 10 \(\Omega\) is stretched to twice its original length. What is the new resistance?
- AP EAPCET - 2025
- Physics
- Resistance
- Two resistors of \(4\, \Omega\) and \(6\, \Omega\) are connected in parallel. What is the equivalent resistance?
- AP EAPCET - 2025
- Physics
- Resistance
- A coil of resistance 10 \( \Omega \) is connected to a battery of 12 V. If the current flowing through the coil is 2 A, what is the power dissipated in the coil?
- BITSAT - 2025
- Physics
- Resistance
- The effective resistance between points A and B in the given circuit is:
- A current of 2 A flows through a conductor with a resistance of 5 \(\Omega\). Calculate the potential difference across the conductor.
- MHT CET - 2025
- Physics
- Resistance
Questions Asked in JEE Main exam
- For a transparent prism, if the angle of minimum deviation is equal to its refracting angle, the refractive index \(n\) of the prism satisfies:
- JEE Main - 2026
- Ray optics and optical instruments
- Let $\vec{a}=2\hat{i}-\hat{j}-\hat{k}$, $\vec{b}=\hat{i}+3\hat{j}-\hat{k}$ and $\vec{c}=2\hat{i}+\hat{j}+3\hat{k}$. Let $\vec{v}$ be the vector in the plane of $\vec{a}$ and $\vec{b}$, such that the length of its projection on the vector $\vec{c}$ is $\dfrac{1}{\sqrt{14}}$. Then $|\vec{v}|$ is equal to
- JEE Main - 2026
- Vector Algebra
- Let \( S = \{x^3 + ax^2 + bx + c : a, b, c \in \mathbb{N} \text{ and } a, b, c \le 20\} \) be a set of polynomials. Then the number of polynomials in \( S \), which are divisible by \( x^2 + 2 \), is:
- JEE Main - 2026
- Algebra
- Figure shows the circuit that contains three resistances (\(9\,\Omega\) each) and two inductors (\(4\,\text{mH}\) each). The reading of ammeter at the moment switch \(K\) is turned ON, is _________ A.
- JEE Main - 2026
- Electromagnetic induction
In the following \(p\text{–}V\) diagram, the equation of state along the curved path is given by \[ (V-2)^2 = 4ap, \] where \(a\) is a constant. The total work done in the closed path is:
- JEE Main - 2026
- Thermodynamics
Concepts Used:
Resistance
Resistance is the measure of opposition applied by any object to the flow of electric current. A resistor is an electronic constituent that is used in the circuit with the purpose of offering that specific amount of resistance.
R=V/I
In this case,
v = Voltage across its ends
I = Current flowing through it
All materials resist current flow to some degree. They fall into one of two broad categories:
- Conductors: Materials that offer very little resistance where electrons can move easily. Examples: silver, copper, gold and aluminum.
- Insulators: Materials that present high resistance and restrict the flow of electrons. Examples: Rubber, paper, glass, wood and plastic.
Resistance measurements are normally taken to indicate the condition of a component or a circuit.
- The higher the resistance, the lower the current flow. If abnormally high, one possible cause (among many) could be damaged conductors due to burning or corrosion. All conductors give off some degree of heat, so overheating is an issue often associated with resistance.
- The lower the resistance, the higher the current flow. Possible causes: insulators damaged by moisture or overheating.