On heating water, bubbles being formed at the bottom of the vessel detatch and rise. Take the bubbles to be spheres of radius $R$ and making a circular contact of radius r with the bottom of the vessel. If $r << R$, and the surface tension of water is T, value of r just before bubbles detatch is (density of water is $\rho_{w}$ )
- $R^{2}\sqrt{\frac{2 \rho_{w}\,g}{3T}}$
- $R^{2}\sqrt{\frac{\rho_{w}\,g}{6T}}$
- $R^{2}\sqrt{\frac{\rho_{w}\,g}{T}}$
- $R^{2}\sqrt{\frac{3\rho_{w}\,g}{T}}$
The Correct Option is A
Solution and Explanation
Top Questions on Surface Tension
- A soap bubble of surface tension \(0.04\,\text{N/m}\) is blown to a diameter of \(7\,\text{cm}\). If \((15000 - x)\,\mu\text{J}\) of work is done in blowing it further to make its diameter \(14\,\text{cm}\) \((\pi = 22/7)\), then the value of \(x\) is ________.
- JEE Main - 2026
- Physics
- Surface Tension
- A soap bubble of diameter $7$ cm, its diameter is increased to $14$ cm. If change in its surface energy is $(15000 - x)\,\mu$J, find $x$. (Given surface tension = $0.04$ N/m)
- JEE Main - 2026
- Physics
- Surface Tension
Consider a water tank shown in the figure. It has one wall at \(x = L\) and can be taken to be very wide in the z direction. When filled with a liquid of surface tension \(S\) and density \( \rho \), the liquid surface makes angle \( \theta_0 \) (\( \theta_0 < < 1 \)) with the x-axis at \(x = L\). If \(y(x)\) is the height of the surface then the equation for \(y(x)\) is: (take \(g\) as the acceleration due to gravity)
- NEET (UG) - 2025
- Physics
- Surface Tension
Two soap bubbles of radius 2 cm and 4 cm, respectively, are in contact with each other. The radius of curvature of the common surface, in cm, is _______________.
- JEE Main - 2025
- Physics
- Surface Tension
- Two water drops each of radius $ r $ coalesce to form a bigger drop. If $ T $ is the surface tension, the surface energy released in this process is:
- JEE Main - 2025
- Physics
- Surface Tension
Questions Asked in JEE Main exam
Inductance of a coil with \(10^4\) turns is \(10\,\text{mH}\) and it is connected to a DC source of \(10\,\text{V}\) with internal resistance \(10\,\Omega\). The energy density in the inductor when the current reaches \( \left(\frac{1}{e}\right) \) of its maximum value is \[ \alpha \pi \times \frac{1}{e^2}\ \text{J m}^{-3}. \] The value of \( \alpha \) is _________.
\[ (\mu_0 = 4\pi \times 10^{-7}\ \text{TmA}^{-1}) \]- JEE Main - 2026
- Ray optics and optical instruments
A small block of mass \(m\) slides down from the top of a frictionless inclined surface, while the inclined plane is moving towards left with constant acceleration \(a_0\). The angle between the inclined plane and ground is \(\theta\) and its base length is \(L\). Assuming that initially the small block is at the top of the inclined plane, the time it takes to reach the lowest point of the inclined plane is _______.
- JEE Main - 2026
- General Physics
- Let \(\vec{a} = -\hat{i} + 2\hat{j} + 2\hat{k}\), \(\vec{b} = 8\hat{i} + 7\hat{j} - 3\hat{k}\) and \(\vec{c}\) be a vector such that \(\vec{a} \times \vec{c} = \vec{b}\). If \(\vec{c} \cdot (\hat{i}+\hat{j}+\hat{k}) = 4\), then \(|\vec{a}+\vec{c}|^2\) is equal to:
- JEE Main - 2026
- Vector Algebra
- Let \( \alpha \) and \( \beta \) respectively be the maximum and the minimum values of the function \( f(\theta) = 4\left(\sin^4\left(\frac{7\pi}{2} - \theta\right) + \sin^4(11\pi + \theta)\right) - 2\left(\sin^6\left(\frac{3\pi}{2} - \theta\right) + \sin^6(9\pi - \theta)\right) \). Then \( \alpha + 2\beta \) is equal to :
- JEE Main - 2026
- Statistics
- The crystal field splitting energy of $[Co(oxalate)_3]^3-$ complex is 'n' times that of the $[Cr(oxalate)_3]^3-$ complex. Here 'n' is_______ (Assume $\Delta_0 > P$)}
- JEE Main - 2026
- Solutions
Concepts Used:
Surface Tension
The amount of energy required to increase the liquid's surface area by one unit area is known as surface tension. In other words, it is a property of the liquid surface to resist force.
Surface tension is defined as,
The ratio of the surface force F to the length L along which the force acts.
Mathematically, the surface tension formula can be expressed as follows:
T=F/L
Where,
- F is the force per unit length
- L is the length in which force act
- T is the surface tension of the liquid
Read More: Detergents and Surface Tension
Factors affecting surface tension:
- Impurities: The surface tension decreases with the addition of impurities.
- Surfactants: Adding surfactants in liquids lowers the tension of water making it interrupt aside or get susceptible.
- Temperature: The surface tension of a liquid reduces as the temperature rises.
The Unit of Surface Tension:
The SI unit of Surface Tension is Newton per Meter or N/m.