Question:
For the same turns per unit length, as the yarn becomes coarser
For the same turns per unit length, as the yarn becomes coarser
Show Hint
- As the yarn becomes coarser, the twist angle increases due to the increase in the yarn diameter.
- The twist multiplier is more relevant to yarns with finer diameters.
- The twist multiplier is more relevant to yarns with finer diameters.
Updated On: Aug 30, 2025
- Twist angle decreases
- Twist angle increases
- Twist multiplier decreases
- Twist multiplier increases
Show Solution
Verified By Collegedunia
The Correct Option is B, D
Solution and Explanation
For yarns with the same turns per unit length, as the yarn becomes coarser, the twist angle increases.
This is because, for coarser yarns, the diameter of the yarn increases, leading to a larger twist angle for the same number of turns per unit length.
Thus, the correct answer is (B).
This is because, for coarser yarns, the diameter of the yarn increases, leading to a larger twist angle for the same number of turns per unit length.
Thus, the correct answer is (B).
Was this answer helpful?
0
0
Top GATE TF Fabric Manufacture, Structure and Properties Questions
- In a projectile weaving machine, the projectile travels through the shed at an average speed of 24 m/s taking \( \frac{2}{3} \) of the loom cycle. If the efficiency of the weaving machine is 90%, the weft insertion rate (m/min) is:
- In a projectile weaving machine, the projectile travels through the shed at an average speed of 24 m/s taking \( \frac{2}{3} \) of the loom cycle. If the efficiency of the weaving machine is 90%, the weft insertion rate (m/min) is:
- Amongst the following, producing a dense fabric in a weaving machine require(s):
Group I lists the components of the weaving machine and Group II lists their functions. Match the component with its function.
- Amongst the following, the component which is NOT a part of single-bed warp knitting machine, is:
View More Questions
Top GATE TF Yarn Questions
A 30 tex cotton yarn is made into a lea of 120 yards for determining CSP. If the lea strength is 500 N, then the CSP of the yarn (rounded off to the nearest integer) is ____
- A 36 Ne ring spun yarn is produced from 1.2 Ne roving. The total draft and the break draft of the roving frame are 12 and 1.2, respectively. The diameters of back bottom roller, middle bottom roller and front bottom roller of the roving frame are 28 mm, 25 mm and 28 mm, respectively. If the middle bottom roller of the roving frame is eccentric, then the wavelength (m) of the periodic fault in the yarn, neglecting twist contraction, (rounded off to 2 decimal places) is \underline{\hspace{2cm}.}
- With reference to the work factor (WF) and work of rupture (WR) of two yarns with the same breaking load and the same breaking elongation, the correct statement(s) is/are
- Amongst the Classimat faults A2, B1, D4, H2 and I1, the correct statement(s) is/are
- A ring spun yarn with mean linear density of 32 tex is produced from 2 denier polyester staple fibre. If the standard deviation of the yarn linear density is 3.2 tex, then the index of irregularity of the yarn (up to 1 decimal place) is:
View More Questions
Top GATE TF Questions
- Polyester fibre is manufactured by the process of:
- GATE TF - 2026
- Yarn Manufacture, Structure and Properties
- Which spinning system produces yarn directly from sliver without roving?
- GATE TF - 2026
- Textile Fibres and its Classification
- The main purpose of scouring in cotton processing is to remove:
- GATE TF - 2026
- Textiles
- The strength of a yarn is commonly expressed in terms of:
- GATE TF - 2026
- Textiles
- In plain weave fabric, the repeat size is:
- GATE TF - 2026
- Yarn Manufacture, Structure and Properties
View More Questions