With regard to superposed folding, the stereographic projection represents a geometry of:
With regard to superposed folding, the stereographic projection represents a geometry of:
Show Hint
- plane cylindrical fold.
- plane non-cylindrical fold.
- non-plane cylindrical fold.
- non-plane non-cylindrical fold.
The Correct Option is B
Solution and Explanation
Step 1: Analyzing the options.
- (A) Plane cylindrical fold: A cylindrical fold is one where the fold's axis remains constant along the entire length, which is not the case in superposed folding.
- (B) Plane non-cylindrical fold: This is the correct answer. A non-cylindrical fold represents a fold where the axis of the fold changes with respect to its position, often seen in superposed folding.
- (C) Non-plane cylindrical fold: This is incorrect because cylindrical folds are typically planar, so the combination of non-plane and cylindrical does not apply in this context.
- (D) Non-plane non-cylindrical fold: This is also incorrect as it does not specifically address the typical characteristics of superposed folding.
Step 2: Conclusion.
The correct answer is (B) plane non-cylindrical fold.
Final Answer: (B) plane non-cylindrical fold.
Top GATE GG Geology Questions
- A type of fold which is relatively sharp and angular at its synformal and antiformal hinges is known as:
- Which of the following time boundaries correspond(s) to major mass extinction events?
Consider two intersecting, north-easterly striking and south-easterly dipping dikes Y1 and Y2, which are exposed on an east-west trending vertical wall of a granite (X) quarry as shown below.
The angle that the dikes make with the horizontal on the quarry wall is
- Which one of the following statements explains why elements Li, Be, and B have low cosmic abundance?
- During a geochemical exploration survey in a hilly terrain, Cu concentration of stream sediments from a third order basin outlet was measured to be 3000 ppm. Considering a catchment area of 10 km\(^2\) and a Cu background value of 200 ppm, which one of the following options is the productivity of this catchment for Cu?
Top GATE GG Structural Geology Questions
- Which of the given folds is/are represented by the stereoplot? \begin{center} \includegraphics[width=0.5\textwidth]{04.jpeg} \end{center}
The given outcrop pattern on a flat topography represents:
- At a certain depth in the crust, the maximum and minimum principal compressive stresses are 150 MPa and 75 MPa, respectively, which lead to normal faulting. If the average density of the crust is 2700 kg/m$^3$, the crustal depth of fracture initiation according to Anderson's theory of faulting is ................ km. (g = 10 m/s$^2$) [round off to one decimal place]
- In the fold profile section shown in the figure, 1 and 3 are the oldest and the youngest stratigraphic units, respectively. Which one of the following fold descriptions CORRECTLY matches the asymmetric fold shown in the given figure?
- Which of the following statements is/are CORRECT for the M-plane of any fault?
Top GATE GG Questions
Is there any good show __________ television tonight? Select the most appropriate option to complete the above sentence.
As the police officer was found guilty of embezzlement, he was ___________ dismissed from the service in accordance with the Service Rules. Select the most appropriate option to complete the above sentence.
- The sum of the following infinite series is: \[ 1 + \frac{1}{1!} + \frac{1}{2!} + \frac{1}{3!} + \frac{1}{4!} + \frac{1}{5!} + \dots \]
- A thin wire is used to construct all the edges of a cube of 1 m side by bending, cutting, and soldering the wire. If the wire is 12 m long, what is the minimum number of cuts required to construct the wire frame to form the cube?
The figures I, II, and III are parts of a sequence. Which one of the following options comes next in the sequence at IV?
