The terminal velocity \((v_t)\) of the spherical rain drop depends on the radius (r) of the spherical rain drop as
- \(r^{\frac 12}\)
- \(r\)
- \(r^2\)
- \(r^3\)
The Correct Option is C
Solution and Explanation
\(6πηvtr = \frac 43πr^3(ρ-σ)g\)
⇒ \(v_t = Cr^2\)
where \(C\) is a constant
⇒ \(v_t ∝ r^2\)
So, the correct option is (C): \(r^2\)
Top Questions on mechanical properties of fluid
- Given below are two statements:
Statement I: Pressure of a fluid is exerted only on a solid surface in contact as the fluid-pressure does not exist everywhere in a still fluid.
Statement II: Excess potential energy of the molecules on the surface of a liquid, when compared to interior, results in surface tension.
In the light of the above statements, choose the correct answer from the options given below- JEE Main - 2026
- Physics
- mechanical properties of fluid
Water flows through a horizontal tube as shown in the figure. The difference in height between the water columns in vertical tubes is 5 cm and the area of cross-sections at A and B are 6 cm\(^2\) and 3 cm\(^2\) respectively. The rate of flow will be ______ cm\(^3\)/s. (take g = 10 m/s\(^2\)).
- JEE Main - 2026
- Physics
- mechanical properties of fluid
- A cylindrical pipe has a radius of \( 0.1 \, \text{m} \). If the speed of water flowing through the pipe is \( 2 \, \text{m/s} \), calculate the volume flow rate of water through the pipe.
- MHT CET - 2025
- Physics
- mechanical properties of fluid
- A pipe has a radius of 2 cm at one end and 1 cm at the other end. The velocity of the water at the wider end is 5 m/s. What is the velocity of the water at the narrower end, assuming incompressible flow?
- MHT CET - 2025
- Physics
- mechanical properties of fluid
- A fluid of density \( 800 \, \text{kg/m}^3 \) is flowing through a pipe of varying cross-sectional area. The velocity of the fluid at point A is \( 2 \, \text{m/s} \), and the velocity at point B is \( 4 \, \text{m/s} \). If the cross-sectional area at point A is \( 1 \, \text{m}^2 \), find the cross-sectional area at point B.
- MHT CET - 2025
- Physics
- mechanical properties of fluid
Questions Asked in JEE Main exam
- \(6 \int_{0}^{\pi} (\sin 3x + \sin 2x + \sin x)dx\) is equal to:
- JEE Main - 2026
- Some Properties of Definite Integrals
- For a transparent prism, if the angle of minimum deviation is equal to its refracting angle, the refractive index \(n\) of the prism satisfies:
- JEE Main - 2026
- Ray optics and optical instruments
- Let $\vec{a}=2\hat{i}-\hat{j}-\hat{k}$, $\vec{b}=\hat{i}+3\hat{j}-\hat{k}$ and $\vec{c}=2\hat{i}+\hat{j}+3\hat{k}$. Let $\vec{v}$ be the vector in the plane of $\vec{a}$ and $\vec{b}$, such that the length of its projection on the vector $\vec{c}$ is $\dfrac{1}{\sqrt{14}}$. Then $|\vec{v}|$ is equal to
- JEE Main - 2026
- Vector Algebra
- Let \( S = \{x^3 + ax^2 + bx + c : a, b, c \in \mathbb{N} \text{ and } a, b, c \le 20\} \) be a set of polynomials. Then the number of polynomials in \( S \), which are divisible by \( x^2 + 2 \), is:
- JEE Main - 2026
- Algebra
- Figure shows the circuit that contains three resistances (\(9\,\Omega\) each) and two inductors (\(4\,\text{mH}\) each). The reading of ammeter at the moment switch \(K\) is turned ON, is _________ A.
- JEE Main - 2026
- Electromagnetic induction
Concepts Used:
Viscosity
Viscosity is a measure of a fluid’s resistance to flow. The SI unit of viscosity is poiseiulle (PI). Its other units are newton-second per square metre (N s m-2) or pascal-second (Pa s.) The dimensional formula of viscosity is [ML-1T-1].
Viscosity: Formula
Viscosity is measured in terms of a ratio of shearing stress to the velocity gradient in a fluid. If a sphere is dropped into a fluid, the viscosity can be determined using the following formula:
η = [2ga2(Δρ)] / 9v
Where ∆ρ is the density difference between fluid and sphere tested, a is the radius of the sphere, g is the acceleration due to gravity and v is the velocity of the sphere.
Viscosity: Types
- Dynamic viscosity: When the viscosity is measured directly by measuring force. It is defined as the ratio of shear stress to the shear strain of the motion. Dynamic viscosity is used to calculate the rate of flow in liquid.
- Kinematic viscosity: There is no force involved. It can be referred to as the ratio between the dynamic viscosity and density of the fluid. It can be computed by dividing the dynamic viscosity of the fluid with fluid mass density.
- Laminar flow: Laminar flow is the type of flow in which the fluid moves smoothly or in a regular path from one layer to the next. Laminar flow occurs in lower velocities.