Question:
Shown below is a wooden artifact made using traditional materials and processes. Which option shows the relevant operations involved in its making, not necessarily in the production sequence?
Shown below is a wooden artifact made using traditional materials and processes. Which option shows the relevant operations involved in its making, not necessarily in the production sequence?
Show Hint
For traditional craft questions, think about the logical progression of material shaping, finishing, and detailing.
Updated On: Jul 7, 2026
- Chiselling, Drilling, Turning, Centering
- Sizing, Turning, Drilling, Lacquering
- Turning, Facing, Balling, Circling
- Turning, Lacquering, Drilling, Chiselling
Show Solution
Verified By Collegedunia
The Correct Option is B
Approach Solution - 1
Step 1: Observe the steps involved in making the wooden artifact. Chiseling and turning are common steps in woodwork, followed by drilling for details and lacquering for finishing.
Step 2: Option B follows a typical order of operations in traditional wooden artifact making.
Step 3: Therefore, the correct answer is (B).
Step 2: Option B follows a typical order of operations in traditional wooden artifact making.
Step 3: Therefore, the correct answer is (B).
Was this answer helpful?
0
0
Show Solution
Verified By Collegedunia
Approach Solution -2
The object shown is a small lathe-turned wooden toy (a rattle/damru-style toy) with a round head, a handle, and a painted finish. Making a piece like this on a lathe follows a fixed order in woodworking: rough the wood to the right size, shape it while it is spinning, drill any holes needed for strings or moving parts only after the main shape exists, and apply the coloured lacquer finish only at the very end, once all cutting and drilling is done, so the finish is not damaged by later machining.
- Option A - Chiselling, Drilling, Turning, Centering: Centering the wood on the lathe has to happen before it is shaped, not after turning, and chiselling by hand is not how a round, lathe-turned toy like this is formed. The order here does not match how the piece would actually be made.
- Option B - Sizing, Turning, Drilling, Lacquering: This follows the real order of the process, cut the wood to size, turn it on the lathe into the round head and handle, drill the holes needed for the strings and the striking balls, then lacquer the finished shape last.
- Option C - Turning, Facing, Balling, Circling: "Balling" and "Circling" are not standard woodworking operations at all, so this option does not describe a real production sequence for the object.
- Option D - Turning, Lacquering, Drilling, Chiselling: Lacquering is placed before drilling here, but drilling and any remaining shaping must always come before the finish coat is applied, otherwise the lacquer would be cut through and damaged.
Only the sizing, turning, drilling, lacquering order in option B matches the sequence a woodworker would actually use to make this toy.
So the correct answer is Sizing, Turning, Drilling, Lacquering.
Was this answer helpful?
0
0
Top CEED Design Aptitude Questions
- A bank needs to upgrade its ATM kiosks to be wheel-chair accessible. An ATM kiosk entrance has four steps rising up to reach the floor level of the kiosk. Each step is 1000 mm in length, 300 mm in breadth, and 150 mm in height. The bank proposes to create a wheel-chair accessible ramp with a slope of 1:12, adjacent to the steps. What is the minimum horizontal length of the ramp in metre? \
- A system of frictionless and massless pulleys is being used to pull up a load of 2520 N. What is the minimum force (in Newtons) required at the end of the rope (shown in dashed lines)?
- Figure shows the plan of a one-way road passing next to a primary school. Which of the options can be the location(s) to set up a bus stop for the school bus in Indian context?
- Mobile sculptures are created by tying fish-shaped cut-outs of different colours using blue strings on brown sticks of negligible weight, as shown below. All the fish cut-outs are of the same size and weight. Which of the options will remain balanced after suspending from a ceiling?
- Which of the graphs shown below represent(s) the equation XY = 25?
View More Questions
Top CEED Logical and Analytical Reasoning Skills Questions
Top CEED Questions
- Solid 1, Solid 2 and Solid 3 are joined together to form a cuboid as shown in Figure 1. The cuboid is then painted from all the sides. How many surfaces are there without the paint when you separate all the three solids?
- An irregular solid is cut into seven pieces as shown. The pieces are neither rotated nor scaled, but are kept in a random sequence. Find the correct sequence to get the smooth form. The sequence should be written from left to right.
- What are the least number of lines required to generate a 3D form such that it creates shadows similar to the figure shown below?
- In the square ABCD, line XY is drawn parallel to the base as shown in the figure below. P and Q are any two arbitrary points on XY, forming triangles ABQ and CDP. What fraction of the area of the square is the total green shaded area?
- Five square pyramids are stacked as shown in the figure below with the bottom layer consisting of four pyramids in a 2 x 2 grid. If the bottom layer consists of pyramids in 6 x 7 grid, and they are stacked in a similar manner to its maximum height, how many pyramids will the formation contain?
View More Questions