Question:
In a direct shear test, the shear strength and normal stress on a dry sand sample at failure are 0.6 kg/cm2 and 10 kg/cm2, respectively. The angle of internal friction of the sand will be nearly
In a direct shear test, the shear strength and normal stress on a dry sand sample at failure are 0.6 kg/cm2 and 10 kg/cm2, respectively. The angle of internal friction of the sand will be nearly
Updated On: Mar 21, 2024
- 25°
- 31°
- 37°
- 43°
Hide Solution
Verified By Collegedunia
The Correct Option is B
Solution and Explanation
The correct answer is (B) : 31°.
Was this answer helpful?
0
0
Top Questions on Maximum Shear Stress Theory
- In a forming operation, the plastic deformation of a steel specimen starts under plane stress condition, where the principal stresses are \(σ_1=200\ Mpa\) and \(σ_2 = 100\ Mpa\). If the steel specimen follows von-Mises yield criterion, then the uniaxial tensile yield strength (in Mpa) of this steel material is ____ . (Rounded off to 1 decimal place)
- GATE PI - 2024
- Strength of Materials
- Maximum Shear Stress Theory
- For a mild steel specimen subjected to uniaxial tensile load, which of the following is/are TRUE?
- GATE PI - 2024
- Strength of Materials
- Maximum Shear Stress Theory
- A cantilever beam of T cross-section carries uniformly distributed load. Where does the maximum magnitude of the bending stress occur?
- CUET (PG) - 2023
- Water Resources Engineering
- Maximum Shear Stress Theory
- Given below are two statements:
Statement - I: Rate of change of shear force (f) at any section of a loaded beam is equal to the Rate of Loading (w) at the section i.e. \(w=\frac{df}{dx}\)
Statement - II: Rate of change of bending moment at any section of a loaded beam represent the shear force (F) at the section is \(f=\frac{dm}{dx}.\)
In the light of the above statements, choose the correct answer from the options given below :- CUET (PG) - 2023
- Water Resources Engineering
- Maximum Shear Stress Theory
- Match List I with List IIChoose the correct answer from the options given below :
List I List II A. Shear force (unit) I. Newton/Area B. Stress II. Newton C. Stain III. Lateral Stain / Axial Stain D. Poisson Ration (N) IV. Change in length / Actual length - CUET (PG) - 2023
- Water Resources Engineering
- Maximum Shear Stress Theory
View More Questions
Questions Asked in CUET PG exam
- What is the standard sequence of steps in a PCR (Polymerase Chain Reaction) cycle?
- CUET (PG) - 2026
- Molecular Biology
- The light pink colour of \([Co(H_2O)_6]^{2+}\) and the deep blue colour of \([CoCl_4]^{2-}\) are due to:
- CUET (PG) - 2026
- Coordination chemistry
- The keys 5, 28, 19, 15, 26, 33, 12, 17, 10 are inserted into a hash table using the hash function $h(k) = k \mod 9$. The collisions are resolved by chaining. After all the keys are inserted, the length of the longest chain is ________. (answer in integer)
- The number of isomers having non-zero dipole moment for \(PCl_2F_3\) in the trigonal bipyramidal geometry is
- CUET (PG) - 2026
- Chemical bonding and molecular structure
- Hybridizations of the atoms indicated with the asterisk (*) in the following compounds sequentially are
- CUET (PG) - 2026
- Chemical bonding and molecular structure
View More Questions