Question:
If work sampling is carried out using a large number of observations, then the required sample size is estimated using
If work sampling is carried out using a large number of observations, then the required sample size is estimated using
Updated On: Jul 12, 2024
- Poisson distribution
- Uniform distribution
- Normal distribution
- Exponential distribution
Show Solution
Verified By Collegedunia
The Correct Option is C
Solution and Explanation
The correct option is (C): Normal distribution.
Was this answer helpful?
0
0
Top GATE PI Industrial Engineering Questions
- In a time study, the average time taken for packaging a product in a warehouse by a worker with 120% performance rating is observed as 9 minutes. Assuming an allowance of 10% of the standard time, the standard time (in minutes) for packaging is ______ . (Answer in integer)
- A thin copper wire carries electric current and is insulated by putting a sleeve, of thickness t, over it. In steady state conditions, the rate of heat loss from the insulated wire per unit length is Q. Which of the following is TRUE?
- The solidification time of a cube and a cylinder of the same material, produced through the same sand casting process, is found to be equal. Each side of the cube is \(a\), and the radius and the length of the cylinder are \(r\) and \(4r\), respectively. If the solidification time is governed by Chvorinov's equation, then the ratio \(\frac ra\) is
- Production and Industrial Engineering (PI) Match each of the listed defects in deep drawing cup with the corresponding reason in the table.
Defect in deep drawing cup Reason P Orange peel on the surface of cup 1 No blank holding force Q Wrinkling at the flange of cup 2 Very small corner radius of the punch R Tearing at the bottom corner of cup 3 Large grain size in the blank material S Earring at the top edge of the cup 4 Anisotropy of the blank material - The following layout of four departments P, Q, R and S is provided as input to CRAFT (Computerized Relative Allocation of Facilities Technique). Which one of the following department pairs cannot be considered for exchange in CRAFT?
View More Questions
Top GATE PI Production Management Questions
- Which of the following concepts is not closely inter-related with INTERCHANGEABILITY in the context of product design?
- Which one of the following THERBLIGS does not advance the progress of the work and can be eliminated by applying the principles of motion economy?
- Which of the following areas is/are supply chain decision(s)?
Top GATE PI Questions
- In an air-standard Otto cycle, the pressure and temperature of air just before the compression stroke are 200 kPa and 26.85 °C, respectively. The combustion process is assumed to be a constant volume process, where 1.02 MJ/kg heat is added. The cycle efficiency is 50%. The adiabatic index \(γ\) and specific heat at constant volume \(C_v\) can be considered to be constant during the process (corresponding values taken at the mean cycle temperature).
Assuming that the ideal gas law is applicable, \(γ = \frac 43\) and \(c_v= 0.85\ kJ/kg-K\), the maximum pressure (in MPa) reached during the cycle is _____ . (Rounded off to 1 decimal place) - A metallic cylindrical pressure vessel, used to store compressed air in a plant, has 1 m mean radius and 4 mm wall thickness. The maximum allowable normal and shear stresses in the cylindrical portion of the vessel are 100 MPa and 40 MPa, respectively. Considering only these data in the design, the maximum allowable internal gauge pressure (in MPa) of the compressed air is ______ . (Rounded off to 2 decimal places)
- A flat belt drive with pulley of r = 20 cm radius is designed to transmit 6.283 kW power at 600 RPM. In the figure, τ is the corresponding torque. If the coefficient of static friction between the belt and the pulley is 0.3, then the minimum value of the tightening force F (in kN) required to prevent the belt slip is _____ . (Rounded off 2 decimal places)
- Mild steel plates are welded to make butt joints by arc welding with 85% heat transfer efficiency ignoring other losses. The first weld joint is made by selecting arc voltage of 30 V and current of 180 A with a welding speed of 6 mm/s. Using identical plates, a second weld joint is made with the same arc voltage and a welding speed of 8 mm/s. If both the welds have the same heat input, then the welding current (in A) for the second weld joint is _____. (Answer in integer)
- In a single pass cold rolling operation, a flat plate is reduced to a thickness of 3 mm. In this operation, two rolls of diameter 400 mm each are rotating in opposite direction at 300 RPM, and the elastic deflection of these rolls is negligible. The angle of bite is 10°. If the neutral point is present at an angle of 7° from the exit side, then the thickness of the plate (in mm) at the neutral point is _____ . (Rounded off to 1 decimal place)
View More Questions