Step 1: Understanding the Concept:
A \(p\)-\(n\) junction is formed when a \(p\)-type and an \(n\)-type semiconductor are joined. Electrons from the \(n\)-side diffuse to the \(p\)-side, and holes diffuse the other way. Near the junction this leaves behind fixed positive donor ions on the \(n\)-side and fixed negative acceptor ions on the \(p\)-side.
This thin region, which has almost no free carriers, is the depletion region. The fixed ions create an electric field and a potential difference \(V_0\) across it, called the potential barrier. It is about 0.7 V for silicon and 0.3 V for germanium.
Step 2: Forward bias:
The \(p\)-side is joined to the positive terminal of the battery and the \(n\)-side to the negative terminal.
The battery field acts against the junction field. Holes on the \(p\)-side and electrons on the \(n\)-side are pushed towards the junction, and they neutralise some of the fixed ions.
So the depletion region becomes narrower, and the potential barrier falls to \(V_0 - V\). Majority carriers can then cross the junction easily, and a large forward current (in mA) flows. The current rises quickly once the applied voltage passes the knee voltage.
Step 3: Reverse bias:
The \(p\)-side is joined to the negative terminal and the \(n\)-side to the positive terminal.
The battery field is now in the same direction as the junction field. It pulls holes and electrons away from the junction, so more fixed ions are uncovered.
So the depletion region becomes wider, and the potential barrier rises to \(V_0 + V\). Majority carriers cannot cross. Only a very small leakage current (in \(\mu\)A) flows, due to minority carriers. This current stays almost constant until breakdown.
Step 4: Full-wave rectifier circuit:
A full-wave rectifier changes the full a.c. input into a pulsating d.c. output. It uses two junction diodes \(D_1\) and \(D_2\) and a centre-tapped transformer.
Circuit connections: The input a.c. is applied to the primary of the transformer. The two ends \(A\) and \(B\) of the secondary are joined to the \(p\)-sides (anodes) of \(D_1\) and \(D_2\). The \(n\)-sides (cathodes) of both diodes are joined together. The load resistance \(R_L\) is connected between this common cathode point and the centre tap \(C\) of the secondary. The output is taken across \(R_L\).
Step 5: Working and the shape of the currents:
In the first half cycle, end \(A\) is positive with respect to the centre tap and end \(B\) is negative. \(D_1\) is forward biased and conducts. \(D_2\) is reverse biased and does not conduct. The current goes through \(R_L\) from the cathode junction towards \(C\).
In the next half cycle, end \(B\) becomes positive and \(A\) negative. \(D_2\) conducts and \(D_1\) is off. The current through \(R_L\) is again in the same direction.
Input: a continuous sine wave which is positive for half a cycle and negative for the next half cycle, with period \(T\).
Output: a series of positive half-sine humps, one for every half cycle of the input, all above the zero line. So the output has no negative part, but it is not steady. It is pulsating d.c.
The output frequency is twice the input frequency (for a 50 Hz supply, the output ripple is 100 Hz). A filter such as a capacitor can then be used to smooth the output.
Final Answer:
Forward bias narrows the depletion region and lowers the barrier, so current flows. Reverse bias widens the region and raises the barrier, so almost no current flows. A centre-tap full-wave rectifier with two diodes gives an output current with positive pulses in both half cycles, at twice the input frequency.
\[ \boxed{f_{\text{out}} = 2 f_{\text{in}}} \]