An instrumentation amplifier has a high
Show Hint
- \( \text{Output impedance} \)
- \( \text{CMRR} \)
- \( \text{Input offset currents} \)
- \( \text{Supply voltage} \)
The Correct Option is B
Solution and Explanation
To solve this problem, we need to understand the key characteristics of an instrumentation amplifier and identify the one with the highest value from the options given.
1. Understanding Instrumentation Amplifiers:
- An Instrumentation Amplifier is a type of differential amplifier with additional input buffering to improve performance. It is designed for precise measurements of small differential signals, often used in sensor applications where high accuracy and stability are required.
Instrumentation amplifiers typically have the following key characteristics:
- High Common-Mode Rejection Ratio (CMRR): This is one of the most important characteristics. CMRR measures the amplifier’s ability to reject common-mode signals (signals that are present on both inputs) while amplifying the differential signal (the difference between the inputs). A high CMRR is essential for reducing the impact of noise or interference that is common to both input signals.
- Low Input Offset Currents: Input offset currents are small mismatches in the input bias currents of the two inputs, which can affect the accuracy of the differential signal measurement. Instrumentation amplifiers are designed to have low input offset currents.
- Low Output Impedance: This typically refers to the impedance seen at the output of the amplifier. While important, it is generally not as high a priority as CMRR in an instrumentation amplifier.
- Supply Voltage: The supply voltage is necessary to power the amplifier but does not typically define its performance in the context of signal processing and rejection of noise or common-mode signals.
2. Key Characteristic of an Instrumentation Amplifier:
The most defining feature of an instrumentation amplifier is its high Common-Mode Rejection Ratio (CMRR). This allows the amplifier to reject unwanted common-mode signals (such as noise or interference) and accurately amplify the differential signal.
Final Answer:
An instrumentation amplifier has a high CMRR (Common-Mode Rejection Ratio).
Top TS PGECET Biomedical Engineering Questions
- The voltage applied to a 212 mH inductor is given by $V(t)=15e^{-5t}$ V. Calculate the current
- The voltage across a capacitor of 0.5F is defined by $V(t)=\begin{cases} 0, & t<0 \\ 2t, & 0<t<2s \\ 4e^{-(t-2)}, & t>2s \end{cases}$. Find $i(t)$
What is the voltage across the inductor at $t=0$? (Circuit diagram provided: A 60V voltage source in series with a switch that closes at $t=0$, a 30 ohm resistor, and a 15H inductor.)
- Which law states that the current flowing into junction must be equal to the current flowing out of it?
- For a voltage source to be neglected, the terminals across the source should be
Top TS PGECET Analog and Digital Electronics Questions
- Slew rate of an ideal op-amp is
- A shunt regulator utilizing a zener diode with an incremental resistance of \(5\,\Omega\) is fed through an \(82\,\Omega\) resistor. If the raw supply changes by \(1.0\,\text{V}\), what is the corresponding change in the regulated output voltage?
- In FET, as \( V_{GS} \) is changed from zero to increasing reverse bias, the value of \( g_m \) is
- An amplifier has an open loop voltage gain of -500. This gain is reduced to -100 when negative feedback is applied. The reverse transmission factor, \( \beta \), of the system is
- The bandwidth of an RF tuned amplifier is dependent on Q-factor of
Top TS PGECET Questions
- If \( P = \begin{pmatrix} 1 & 1 & 1 \\ 0 & 1 & 2 \\ 0 & 0 & 1 \end{pmatrix} \) is the modal matrix of \( A = \begin{pmatrix} 1 & 1 & 0 \\ 0 & 2 & 2 \\ 0 & 0 & 3 \end{pmatrix} \) then the sum of all the elements of \( P^{-1}AP \) is
- If the system of equations \( kx + y + z = k - 1 \), \( x + ky + z = k - 1 \), and \( x + y + kz = k - 1 \) has infinite solutions, then \( k \) is
- The value of the integral \( \int_C (2xy - x^2) \, dx + (x^2 + y^2) \, dy \) where \( C \) is the boundary of the region enclosed by \( y = x^2 \) and \( y^2 = x \), described in the positive sense, is
- Let \( f(x) = \log x \). The number \( C \) strictly between \( e^2 \) and \( e^3 \) such that its reciprocal is equal to \( \frac{f(e^3) - f(e^2)}{e^3 - e^2} \) is
- The solution of the differential equation \( (D^2 + 2)y = x^2 \) is