Question:
A CNC milling operation is carried out by moving the tool from the point A to point B in anti-clockwise direction to cut a slot of quarter circle with center at C, as shown. The coordinates of the points A and B are (0,0) and (10,10), respectively. All dimensions are in mm. If the feed rate at point P along x-axis is 6 mm/min, then the feed rate (in mm/min) at point P along y-axis is ______ . (Rounded off to 1 decimal place)
A CNC milling operation is carried out by moving the tool from the point A to point B in anti-clockwise direction to cut a slot of quarter circle with center at C, as shown. The coordinates of the points A and B are (0,0) and (10,10), respectively. All dimensions are in mm. If the feed rate at point P along x-axis is 6 mm/min, then the feed rate (in mm/min) at point P along y-axis is ______ . (Rounded off to 1 decimal place)
Updated On: Jan 9, 2026
Show Solution
Verified By Collegedunia
Correct Answer: 4.5
Solution and Explanation
The answer is 4.5
Was this answer helpful?
1
8
Top GATE PI Manufacturing Processes II Questions
- The following data are given in relation to turning operation of a cylindrical workpiece.
Diameter of the workpiece = 160 mm, length of the workpiece = 190 mm, cutting velocity = 80 m/min, and tool feed = 0.2 mm/rev.
Assuming the approach and the overrun of the tool to be 5 mm each, the machining time (in minutes) is _____ . (Answer in integer) - During orthogonal turning, the cutting speed, feed and depth of cut are set as 2 m/s, 0.2 mm/rev and 2 mm, respectively. The specific cutting energy (neglecting the effect of feed force on the total cutting power) is 2 J/mm3. The main cutting force (in N) is _____ . (Answer in integer)
- Electro-chemical machining is performed on a flat copper workpiece. If the material removal rate is \(2\ cm^3/min\) throughout the process, then the required current (in A) is ______ . (Rounded off to 1 decimal place)
Copper properties: Melting point = \(1085 °C\), density = \(9\ g/cm^3\), gram atomic weight = \(63\), and valency of dissolution = \(2\)
Faraday's constant = \(96500 C\)
Stefan-Boltzmann constant = \(5.67 \times 10^{-8} W/m^2-K^4\) - An offset slider-crank mechanism is shown in the figure. If the length l = 10 cm, then the stroke length (in cm) of the slider is _____ . (Rounded off to 1 decimal place)
- Choose the item(s) which is/are required to make an eccentric hole on a disc, as shown, using a lathe.
View More Questions
Top GATE PI Machining parameters and material removal rate Questions
- During orthogonal turning, the cutting speed, feed and depth of cut are set as 2 m/s, 0.2 mm/rev and 2 mm, respectively. The specific cutting energy (neglecting the effect of feed force on the total cutting power) is 2 J/mm3. The main cutting force (in N) is _____ . (Answer in integer)
- Electro-chemical machining is performed on a flat copper workpiece. If the material removal rate is \(2\ cm^3/min\) throughout the process, then the required current (in A) is ______ . (Rounded off to 1 decimal place)
Copper properties: Melting point = \(1085 °C\), density = \(9\ g/cm^3\), gram atomic weight = \(63\), and valency of dissolution = \(2\)
Faraday's constant = \(96500 C\)
Stefan-Boltzmann constant = \(5.67 \times 10^{-8} W/m^2-K^4\) A cylindrical workpiece is turned using two different tools. Tool 1 has zero nose radius; the side and end cutting edge angles are \(20^\circ\) and \(10^\circ\), respectively. Tool 2 has a 0.5 mm nose radius. Both tools machine at a feed of \(0.2\ \text{mm/rev}\). The ratio of the ideal maximum height of unevenness on the surface produced by Tool 1 to that produced by Tool 2 is \(\underline{\hspace{2cm}}\) (round off to one decimal place).
Top GATE PI Questions
- In an air-standard Otto cycle, the pressure and temperature of air just before the compression stroke are 200 kPa and 26.85 °C, respectively. The combustion process is assumed to be a constant volume process, where 1.02 MJ/kg heat is added. The cycle efficiency is 50%. The adiabatic index \(γ\) and specific heat at constant volume \(C_v\) can be considered to be constant during the process (corresponding values taken at the mean cycle temperature).
Assuming that the ideal gas law is applicable, \(γ = \frac 43\) and \(c_v= 0.85\ kJ/kg-K\), the maximum pressure (in MPa) reached during the cycle is _____ . (Rounded off to 1 decimal place) - A metallic cylindrical pressure vessel, used to store compressed air in a plant, has 1 m mean radius and 4 mm wall thickness. The maximum allowable normal and shear stresses in the cylindrical portion of the vessel are 100 MPa and 40 MPa, respectively. Considering only these data in the design, the maximum allowable internal gauge pressure (in MPa) of the compressed air is ______ . (Rounded off to 2 decimal places)
- A flat belt drive with pulley of r = 20 cm radius is designed to transmit 6.283 kW power at 600 RPM. In the figure, τ is the corresponding torque. If the coefficient of static friction between the belt and the pulley is 0.3, then the minimum value of the tightening force F (in kN) required to prevent the belt slip is _____ . (Rounded off 2 decimal places)
- Mild steel plates are welded to make butt joints by arc welding with 85% heat transfer efficiency ignoring other losses. The first weld joint is made by selecting arc voltage of 30 V and current of 180 A with a welding speed of 6 mm/s. Using identical plates, a second weld joint is made with the same arc voltage and a welding speed of 8 mm/s. If both the welds have the same heat input, then the welding current (in A) for the second weld joint is _____. (Answer in integer)
- In a single pass cold rolling operation, a flat plate is reduced to a thickness of 3 mm. In this operation, two rolls of diameter 400 mm each are rotating in opposite direction at 300 RPM, and the elastic deflection of these rolls is negligible. The angle of bite is 10°. If the neutral point is present at an angle of 7° from the exit side, then the thickness of the plate (in mm) at the neutral point is _____ . (Rounded off to 1 decimal place)
View More Questions