>
Exams
>
Mechanical Engineering
>
Metrology and Measurements
>
which is the correct type of configuration of a cm
Question:
Which is the correct type of configuration of a CMM from the figure presented below?
Show Hint
The moving bridge configuration provides high stability and precision, making it ideal for accurate measurements in CMMs.
TANCET - 2024
TANCET
Updated On:
Feb 27, 2025
Column type
Gantry type
Moving bridge
Moving lever cantilever arm
Show Solution
Verified By Collegedunia
The Correct Option is
C
Solution and Explanation
The moving bridge configuration of a Coordinate Measuring Machine (CMM) is the most common. In this configuration, the bridge spans across the measurement area, with the probe moving along the X, Y, and Z axes to measure the part.
Download Solution in PDF
Was this answer helpful?
0
0
Top TANCET Mechanical Engineering Questions
A bullet is fired upwards at an angle of \(30^\circ\) to the horizontal from a point P on a hill, and it strikes a target which is 80 m lower than P. The initial velocity of the bullet is 100 m/s. Calculate the maximum height to which the bullet will rise above the horizontal. Assume \( g = 9.81 \) m/s\(^2\).
TANCET - 2024
Mechanical Engineering
Mechanics
View Solution
The condition for a screw jack to be self-locking is that:
TANCET - 2024
Mechanical Engineering
Machine Design
View Solution
The first moment of area of a semicircular area about its diameter ‘d’ is given by:
TANCET - 2024
Mechanical Engineering
Strength of Materials
View Solution
A reciprocating pump driven by a driving wheel is shown in the below figure. If the crank is 80 mm long and the connecting rod is 200 mm, determine the velocity of the piston in the position shown. The driving wheel rotates at 2000 rpm in the anticlockwise direction.
TANCET - 2024
Mechanical Engineering
Kinetics and Dynamics
View Solution
A 5-kg uniform serving table is supported on each side by two pairs of identical links, AB and CD, and springs CE as shown in the below figure. If the bowl has a mass of 1 kg and is in equilibrium when \( \theta = 45^\circ \), determine the stiffness \( k \) of each spring. The springs are unstretched when \( \theta= 90^\circ \). Neglect the mass of the links.
TANCET - 2024
Mechanical Engineering
Kinetics and Dynamics
View Solution
View More Questions
Top TANCET Metrology and Measurements Questions
Inside size of slots or holes can be measured by
TANCET - 2024
Mechanical Engineering
Metrology and Measurements
View Solution
Which of the following provides a quick-fix means of conducting an initial investigation before attempting a major investigation of surface quality?
TANCET - 2024
Mechanical Engineering
Metrology and Measurements
View Solution
Top TANCET Questions
If \( A \) is a \( 3 \times 3 \) matrix and the determinant of \( A \) is 6, then find the value of the determinant of the matrix \( (2A)^{-1} \):
TANCET - 2024
Matrices and Determinants
View Solution
If the system of equations:
\[ 3x + 2y + z = 0, \quad x + 4y + z = 0, \quad 2x + y + 4z = 0 \]
is given, then:
TANCET - 2024
Linear Algebra
View Solution
Let
\[ M = \begin{bmatrix} 1 & 1 & 1 \\ 0 & 1 & 1 \\ 0 & 0 & 1 \end{bmatrix} \]
The maximum number of linearly independent eigenvectors of \( M \) is:
TANCET - 2024
Eigenvalues and Eigenvectors
View Solution
The shortest and longest distance from the point \( (1,2,-1) \) to the sphere \( x^2 + y^2 + z^2 = 24 \) is:
TANCET - 2024
3D Geometry
View Solution
The solution of the given ordinary differential equation \( x \frac{d^2 y}{dx^2} + \frac{dy}{dx} = 0 \) is:
TANCET - 2024
Quadratic Equation
View Solution
View More Questions