Match the machine elements with their functions.
Match the machine elements with their functions.
Show Hint
- P – 3, Q – 2, R – 1
- P – 3, Q – 1, R – 2
- P – 2, Q – 1, R – 3
- P – 1, Q – 3, R – 2
The Correct Option is B
Solution and Explanation
- A dividing head (Q) is used for indexing, which is function 1.
- A lead screw (R) is used for thread cutting, which corresponds to function 2.
Top Questions on Industrial and Production
- Three principal stresses at a point in a material are 300 MPa, 250 MPa, and 100 MPa. If the yielding just starts at that point, the yield strength (in MPa) of the material as per Tresca criterion is ............
Answer: The yield strength lies between 199 to 201 MPa.- GATE PI - 2025
- Production and Industrial Engineering
- Industrial and Production
- Two options are available to meet the annual demand of batteries in a toy company. In option 1, batteries are manufactured in the plant having fixed cost of Rupees 2,00,000 and a variable cost of Rupees 70 per unit. Option 2 consists of buying batteries from the market at a price of Rupees 90 per unit. The annual demand (in number of batteries) at which the company should switch from buying to making the batteries in the plant is .......... (Answer in integer)
- GATE PI - 2025
- Production and Industrial Engineering
- Industrial and Production
- While inspecting final assembly of automobile-gear-boxes, 15 features were considered critical-to-quality (CTQ). During last quarter, 40000 gear boxes were produced among which 1500 defects were found of the CTQ features. The defects per million opportunities (DPMO) is .......... (Answer in integer)
- GATE PI - 2025
- Production and Industrial Engineering
- Industrial and Production
The hole and the shaft dimensions (in mm) are given as
Hole dimension = \(30 \pm 0.04\) and Shaft dimension = \(30 \pm 0.06\).
The maximum possible clearance (in mm) is .......... (Rounded off to two decimal places)
- GATE PI - 2025
- Production and Industrial Engineering
- Industrial and Production
- The value of the integral \[ \int_1^3 \left( x^2 - 2x \right) \, dx \] obtained by using Simpson’s 1/3 rule with 4 subintervals is equal to \( \frac{n}{3} \). The value of \( n \) is .............
- GATE PI - 2025
- Production and Industrial Engineering
- Industrial and Production
Questions Asked in GATE PI exam
A through hole of 10 mm diameter is to be drilled in a mild steel plate of 30 mm thickness. The selected spindle speed and feed for drilling hole are 600 revolutions per minute (RPM) and 0.3 mm/rev, respectively. Take initial approach and breakthrough distances as 3 mm each. The total time (in minute) for drilling one hole is ______. (Rounded off to two decimal places)
- GATE PI - 2026
- Machining Processes and Machine Tools
In a cold rolling process without front and back tensions, the required minimum coefficient of friction is 0.04. Assume large rolls. If the draft is doubled and roll diameters are halved, then the required minimum coefficient of friction is ___________. (Rounded off to two decimal places)
- GATE PI - 2026
- Machining Processes and Machine Tools
- Which one of the following casting defects is caused due to the supply of the molten metal through two gates?
- GATE PI - 2026
- Machining Processes and Machine Tools
- The relationship between the hoop stress \(\sigma_1\) and the longitudinal stress \(\sigma_2\) of a closed cylindrical thin-walled pressure vessel is
- GATE PI - 2026
- Machining Processes and Machine Tools
- In an orthogonal straight turning process, the feed is 0.1 mm/rev and the depth of cut is 0.5 mm. In ASA system, the side cutting edge angle of the cutting tool is 0°. The width (in mm) of the chip is ............ (Rounded off to one decimal place)
- GATE PI - 2025
- Cutting forces