Question:
In which of the following, number of teeth decides the Noil % in Comber
In which of the following, number of teeth decides the Noil % in Comber
Show Hint
In comber, ratchet teeth control feed length, which directly influences noil percentage.
Updated On: Jul 4, 2026
- Circular Bevel
- Worm Wheel
- Ratchet
- Helical gear
Show Solution
Verified By Collegedunia
The Correct Option is C
Solution and Explanation
Concept:
In a comber, the feed motion is controlled by a ratchet mechanism. The number of ratchet teeth determines the amount of feed given per cycle. Since feed length directly affects fibre selection, it also controls the noil percentage.
Step 1: Understand feed mechanism.
Comber feed is controlled in discrete steps using ratchet and pawl mechanism. \[ \text{Ratchet teeth} \Rightarrow \text{Feed length control} \]
Step 2: Relate feed to noil.
• More feed → less fibre removal → lower noil
• Less feed → more fibre removal → higher noil
Step 3: Identify correct component.
Only ratchet mechanism directly uses number of teeth to control motion.
Step 4: Final answer selection.
Thus, \[ \boxed{\text{Ratchet}} \] So, \[ \boxed{\text{Option (C) is correct.}} \]
Step 1: Understand feed mechanism.
Comber feed is controlled in discrete steps using ratchet and pawl mechanism. \[ \text{Ratchet teeth} \Rightarrow \text{Feed length control} \]
Step 2: Relate feed to noil.
• More feed → less fibre removal → lower noil
• Less feed → more fibre removal → higher noil
Step 3: Identify correct component.
Only ratchet mechanism directly uses number of teeth to control motion.
Step 4: Final answer selection.
Thus, \[ \boxed{\text{Ratchet}} \] So, \[ \boxed{\text{Option (C) is correct.}} \]
Was this answer helpful?
0
0
Top TS PGECET Textile Engineering and Fibre Science Questions
- SERICIN refers to
- From the following, highest moisture regain can be seen in
- The trilobal cross section of polyester is observed in
- In which of the following cotton, one finds an apparel use?
- Basalt is
View More Questions
Top TS PGECET Yarn Engineering Questions
- The number of coils /D.T$_t$ remains constant from D$_0$ to D$_{max}$ in
- Alpanol is a best example of
- Compared to Single yarn, in Double or folded yarns the Uniformity will
- In Comber preparatory, as the Pre-Comb draft increases, the Noil % will
- In Modern Comber, use of half moon shaped Web it is possible to achieve Combed Sliver with
View More Questions
Top TS PGECET Questions
- If \( P = \begin{pmatrix} 1 & 1 & 1 \\ 0 & 1 & 2 \\ 0 & 0 & 1 \end{pmatrix} \) is the modal matrix of \( A = \begin{pmatrix} 1 & 1 & 0 \\ 0 & 2 & 2 \\ 0 & 0 & 3 \end{pmatrix} \) then the sum of all the elements of \( P^{-1}AP \) is
- If the system of equations \( kx + y + z = k - 1 \), \( x + ky + z = k - 1 \), and \( x + y + kz = k - 1 \) has infinite solutions, then \( k \) is
- The value of the integral \( \int_C (2xy - x^2) \, dx + (x^2 + y^2) \, dy \) where \( C \) is the boundary of the region enclosed by \( y = x^2 \) and \( y^2 = x \), described in the positive sense, is
- Let \( f(x) = \log x \). The number \( C \) strictly between \( e^2 \) and \( e^3 \) such that its reciprocal is equal to \( \frac{f(e^3) - f(e^2)}{e^3 - e^2} \) is
- The solution of the differential equation \( (D^2 + 2)y = x^2 \) is
View More Questions