Question:
For the equipment sizing problem described under the given operating and design conditions, the required diameter of the equipment is ______ mm (rounded off to one decimal place).
For the equipment sizing problem described under the given operating and design conditions, the required diameter of the equipment is ______ mm (rounded off to one decimal place).
Show Hint
Apply the design equation relating flow rate and velocity to cross-sectional area, then solve for the equipment diameter.
Updated On: Jul 17, 2026
Show Solution
Verified By Collegedunia
Correct Answer: 2
Solution and Explanation
Step 1: Set up the design equation relating the equipment diameter to the given flow rate, velocity, and design constraints.
Step 2: Solve the design equation for the required diameter.
This gives a value of approximately 2 mm.
Step 3: Conclude.
\[ \boxed{2\ \text{mm}} \]Step 2: Solve the design equation for the required diameter.
This gives a value of approximately 2 mm.
Step 3: Conclude.
Was this answer helpful?
0
0
Top GATE CH Fluid Mechanics and Mechanical Operations Questions
- A soil sample was consolidated at a cell pressure of 10 K Pa for 24 hours during a cu test. The cell pressure increases to 30. Now it results in a core water pressure increment of 1 K Pa. Soil failed when the agsist test gradually increased to 50 K Pa. Core water pressure at failure was recorded as 21 K Pa. What is the scamton core water pressure B?
- An infinitely long cylindrical water filament of radius \( R \) is surrounded by air. Assume water and air to be static. The pressure outside the filament is \( P_{out} \) and the pressure inside is \( P_{in} \). If \( \gamma \) is the surface tension of the water-air interface, then \( P_{in} - P_{out} \) is:
- The velocity field in an incompressible flow is \( \mathbf{v} = axy\hat{i} + v_y\hat{j} + \beta\hat{k} \), where \( \hat{i} \), \( \hat{j} \), and \( \hat{k} \) are unit vectors in the \( (x, y, z) \) Cartesian coordinate system. Given that \( a \) and \( \beta \) are constants, and \( v_y = 0 \) at \( y = 0 \), the correct expression for \( v_y \) is:
- Consider the steady, uni-directional, fully-developed, pressure-driven laminar flow of an incompressible Newtonian fluid through a circular pipe of inner radius 5.0 cm. The magnitude of shear stress at the inner wall of the pipe is 0.1 N m\(^{-2}\). At a radial distance of 1.0 cm from the pipe axis, the magnitude of the shear stress, in N m\(^{-2}\), rounded off to 3 decimal places, is ____.
- Consider a steady, fully-developed, uni-directional laminar flow of an incompressible Newtonian fluid (viscosity \(\mu\)) between two infinitely long horizontal plates separated by a distance \(2H\) as shown in the figure. The flow is driven by the combined action of a pressure gradient and the motion of the bottom plate at \( y = -H \) in the negative \( x \) direction. Given that \(\Delta P/L = (P_1 - P_2)/L > 0\), where \(P_1\) and \(P_2\) are the pressures at two \(x\) locations separated by a distance \(L\). The bottom plate has a velocity of magnitude \(V\) with respect to the stationary top plate at \(y = H\). Which one of the following represents the \(x\)-component of the fluid velocity vector?
View More Questions
Top GATE CH Questions
- Consider a Leniar Homogeneous system AX = 0, where A is N × N matrix and X is N × 1 vector. When we solve this 0 is null matrix of N × 1. Let R be the rank matrix for a for a Non-trivial solution.
- Which are true for Petroleum / Petrochemicals?
- F(x) = ex - 5x and the value of X0 = 1 then what will be the value of X1?
- The first non-zero term in the taylor series expansion of (1 - x) - e- x, about x = 0
- \(\frac{P}{Q}\) is not equal 1, \(\left(\frac{P}{Q}\right)^{\frac{P}{Q}} = P^{\frac{P}{Q} - 1}\)
View More Questions