Question:
Creep of mild steel at elevated temperature involves
Creep of mild steel at elevated temperature involves
Show Hint
Creep in materials, especially metals like steel, occurs when the material is subjected to a constant load at elevated temperatures, leading to plastic deformation over time.
Updated On: Sep 4, 2025
- elastic deformation under constant load
- elastic deformation under dynamic load
- plastic deformation under constant load
- plastic deformation under dynamic load
Show Solution
Verified By Collegedunia
The Correct Option is C
Solution and Explanation
Creep is the slow, time-dependent deformation of a material under a constant load, typically occurring at elevated temperatures. For mild steel, at elevated temperatures, the material undergoes plastic deformation under a constant load over time. Hence, creep is associated with plastic deformation under constant load.
Thus, the correct answer is (C).
Thus, the correct answer is (C).
Was this answer helpful?
0
0
Top GATE PI Engineering Sciences Questions
- A solid circular disk of 0.025 m thickness is used as a flywheel. The density of the disk material is 7800 kg/m³ and the mass moment of inertia of the disk about its center is 4.36 kg·m². The radius, in m, of the disk is ................. (round off to 2 decimal places).
- A metal rod of diameter 14 mm is subjected to a tensile test. After the test, its cross-sectional diameter at the fractured end is 12 mm. The ductility, in %, is ................. (round off to 2 decimal places).
Match the engineering materials at room temperature with the given crystal structures.
- A cylindrical casting has 10 cm diameter and a mass of 12.56 kg. The material density is \( 7.85 \times 10^{-3} \, \text{kg/cm}^3 \). The value of exponent \(n\) is 2 and solidification time is 12 min. The Chvorinov's constant, in min/cm\(^2\), is ................. (round off to 2 decimal places).
Top GATE PI Material Science Questions
- A solid circular disk of 0.025 m thickness is used as a flywheel. The density of the disk material is 7800 kg/m³ and the mass moment of inertia of the disk about its center is 4.36 kg·m². The radius, in m, of the disk is ................. (round off to 2 decimal places).
- A metal rod of diameter 14 mm is subjected to a tensile test. After the test, its cross-sectional diameter at the fractured end is 12 mm. The ductility, in %, is ................. (round off to 2 decimal places).
Match the engineering materials at room temperature with the given crystal structures.
- A cylindrical casting has 10 cm diameter and a mass of 12.56 kg. The material density is \( 7.85 \times 10^{-3} \, \text{kg/cm}^3 \). The value of exponent \(n\) is 2 and solidification time is 12 min. The Chvorinov's constant, in min/cm\(^2\), is ................. (round off to 2 decimal places).
Top GATE PI Questions
- In an air-standard Otto cycle, the pressure and temperature of air just before the compression stroke are 200 kPa and 26.85 °C, respectively. The combustion process is assumed to be a constant volume process, where 1.02 MJ/kg heat is added. The cycle efficiency is 50%. The adiabatic index \(γ\) and specific heat at constant volume \(C_v\) can be considered to be constant during the process (corresponding values taken at the mean cycle temperature).
Assuming that the ideal gas law is applicable, \(γ = \frac 43\) and \(c_v= 0.85\ kJ/kg-K\), the maximum pressure (in MPa) reached during the cycle is _____ . (Rounded off to 1 decimal place) - A metallic cylindrical pressure vessel, used to store compressed air in a plant, has 1 m mean radius and 4 mm wall thickness. The maximum allowable normal and shear stresses in the cylindrical portion of the vessel are 100 MPa and 40 MPa, respectively. Considering only these data in the design, the maximum allowable internal gauge pressure (in MPa) of the compressed air is ______ . (Rounded off to 2 decimal places)
- A flat belt drive with pulley of r = 20 cm radius is designed to transmit 6.283 kW power at 600 RPM. In the figure, τ is the corresponding torque. If the coefficient of static friction between the belt and the pulley is 0.3, then the minimum value of the tightening force F (in kN) required to prevent the belt slip is _____ . (Rounded off 2 decimal places)
- Mild steel plates are welded to make butt joints by arc welding with 85% heat transfer efficiency ignoring other losses. The first weld joint is made by selecting arc voltage of 30 V and current of 180 A with a welding speed of 6 mm/s. Using identical plates, a second weld joint is made with the same arc voltage and a welding speed of 8 mm/s. If both the welds have the same heat input, then the welding current (in A) for the second weld joint is _____. (Answer in integer)
- In a single pass cold rolling operation, a flat plate is reduced to a thickness of 3 mm. In this operation, two rolls of diameter 400 mm each are rotating in opposite direction at 300 RPM, and the elastic deflection of these rolls is negligible. The angle of bite is 10°. If the neutral point is present at an angle of 7° from the exit side, then the thickness of the plate (in mm) at the neutral point is _____ . (Rounded off to 1 decimal place)
View More Questions